Driver sr need updating gentoo play naruto dating games online

Posted by / 16-May-2017 00:00

Driver sr need updating gentoo

Password: gen ~ # There are pretty good instructions in Xorg/Configuration. Carefully examine the list of proposed changes, paying special attention to mask or keyword changes that may expose experimental or unstable packages. * IMPORTANT: config file '/etc/portage/package.use' needs updating.

We already had all the kernel options set and we had the settings configured as well (we had added the following to the /etc/conf file): gen ~ # emerge xorg-server * IMPORTANT: 8 news items need reading for repository 'gentoo'. * See the CONFIGURATION FILES section of the emerge * man page to learn how to update config files. The following is the list of files which need updating, each configuration file is followed by a list of possible replacement files.

We need to tell our system where swap is and other partitions as well, here is how my /etc/fstab file looked like in the end: livecd ~ # exit exit livecd gentoo # umount -l /mnt/gentoo/sys livecd gentoo # umount -l /mnt/gentoo/dev livecd gentoo # umount /mnt/gentoo/proc livecd gentoo # umount /mnt/gentoo/boot livecd gentoo # umount -l /mnt/gentoo livecd gentoo # poweroff livecd gentoo # Broadcast message from [email protected] (pts/0) (Wed Nov 12 2014): The system is going down for system halt NOW!

[email protected]:~$ssh -p 2244 -l root localhost @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED!

:) into ~/.xinitrc and then running startx will start the icewm.

If any ethernet adapters were detected at boot, they should be auto-configured if DHCP is available on your network.Found linux image: /boot/vmlinuz-3.16.5-gentoo Found initrd image: /boot/initramfs-genkernel-x86_64-3.16.5-gentoo done At this point we can probably reboot and it will should boot up.But before we do that let’s enable system logging and other necessary components.To start an ssh server on this system, type "/etc/init.d/sshd start". Performing Global Updates (Could take a couple of minutes if you have a lot of binary packages.) * IMPORTANT: 8 news items need reading for repository 'gentoo'. livecd / # livecd / # eselect profile list Available profile symlink targets: [1] default/linux/amd64/13.0 * [2] default/linux/amd64/13.0/selinux [3] default/linux/amd64/13.0/desktop [4] default/linux/amd64/13.0/desktop/gnome [5] default/linux/amd64/13.0/desktop/gnome/systemd [6] default/linux/amd64/13.0/desktop/kde [7] default/linux/amd64/13.0/desktop/kde/systemd [8] default/linux/amd64/13.0/developer [9] default/linux/amd64/13.0/no-emul-linux-x86 [10] default/linux/amd64/13.0/no-emul-linux-x86/desktop [11] default/linux/amd64/13.0/no-multilib [12] default/linux/amd64/13.0/x32 [13] hardened/linux/amd64 [14] hardened/linux/amd64/selinux [15] hardened/linux/amd64/no-multilib [16] hardened/linux/amd64/no-multilib/selinux [17] hardened/linux/amd64/x32 [18] hardened/linux/musl/amd64 [19] default/linux/uclibc/amd64 [20] hardened/linux/uclibc/amd64 [X] Symmetric multi-processing support (keep this enabled for multiple cores, too!If you need to log in remotely as root, type "passwd root" to reset root's password to a known value. Be sure to include detailed information about how to reproduce the bug you are reporting. livecd ~ # livecd ~ # fdisk -l /dev/sda Disk /dev/sda: 20 Gi B, 21474836480 bytes, 41943040 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes livecd ~ # fdisk /dev/sda Welcome to fdisk (util-linux 2.24.1). ) [X] SMT (Hyperthreading) scheduler support (This too, for i7's) [ ] Machine Check / overheating reporting Power management and ACPI options --- All of the above options were already enabled except the audio card: As a side note, if you don’t want to mess with the config, you can always just use the same config that the livecd is using.

driver sr need updating gentoo-36driver sr need updating gentoo-33driver sr need updating gentoo-22

Type "net-setup eth0" to specify eth0 IP address settings by hand.

One thought on “driver sr need updating gentoo”